Load Legs 101: What Is a Load Leg?

Load Legs—Foot Props—Stability Legs—Anti-Rebound Bars

Updated September 2022

Load legs were first introduced to Americans in 2004 by Britax on the Baby Safe, a short-lived rear-facing only seat popular in Europe, but we weren’t quite ready for it. It had an anti-rebound bar, rigid LATCH, and a load leg: things American consumers simply didn’t understand, or want to pay the hefty price tag for at the time. Today’s shoppers are more sophisticated and researching such features is second-nature now.

Let’s address why load legs—aka foot props or stability legs—exist. Here on this side of the Atlantic, we find them on rear-facing only infant seats and the new Cybex Sirona S convertible carseat, but in Europe, you will find them also on forward-facing carseats. Load legs limit downward rotation toward the front of the vehicle. Statistically, frontal crashes account for the majority of crashes so we design carseats to protect children in them. Carseats move toward the point of impact, so rear-facing carseats rotate down and toward the front of the vehicle in a frontal impact.

According to FMVSS 213, the safety standard to which all U.S. carseats are tested, rear-facing carseats may rotate downward up to 70° and still pass testing. During this downward rotation, the child will also ramp up (slide up) the carseat. As the child slides up the seat, crash forces are felt in the neck and shoulders as they make contact with the harness.

Harnesses, seat belts, and LATCH belt webbing are designed to stretch for energy management. This stretching of the webbing—plus any removal of slack in the harness—and vehicle seat cushion compression causing downward rotation, is called “payout.” Payout happens before ride down, which is when the carseat and vehicle come to a stop. The more movement a child has during a crash, the more chance for injury, which is why child passenger safety technicians emphasize snug harnesses and installations. Eliminating the downward rotation by using a load leg means the child stays down in the seat and payout is reduced. This is a good thing because the less time that’s spent on payout, the more time that’s spent on ride down, which is when the carseat itself starts absorbing energy. The carseat stays more upright allowing the back of the carseat to absorb energy instead of the harness; the crash forces are distributed along the child’s back instead of concentrated on the neck and shoulders.

Another benefit from load legs, especially in smaller vehicles, is that by allowing the carseat to stay more upright in a crash, there’s less of a chance a child will ramp up and out of the carseat and strike the vehicle interior with their head. Head injuries lead the list of injuries to rear-facing children in vehicle crashes.

The video below compares a Cybex Aton 2 without its load leg to an Aton 2 with its load leg. You can see how a load leg affects downward rotation. Be sure to notice the position of the dummy’s head on each side of the video.

Another thing to point out with load legs involves FMVSS 213 and testing with load legs. The test sled for 213 doesn’t have a floor, so load legs can’t officially be included in federal testing. Frustratingly enough, NHTSA won’t add a floor to the test sled to officially crash test load legs because it feels that caregivers won’t use the load leg feature. I wish we were kidding.

When manufacturers test their carseats with load legs, they add a floor piece onto the sled so the load leg has a place to rest and NHTSA allows this practice. It’s part of that “extra testing” that manufacturers do to their carseats that their marketing department then labels on the box. This is why load legs aren’t required to be used and bases with this accessory have a storage area for them to be tucked away.

What about Rebound?

We can’t really talk about load legs without discussing rebound. Rebound is the action of a rear-facing carseat when the top part of it moves toward the back seat upon pushing or collision. On a carseat without a load leg, after the downward rotation, there will be rebound (remember Newton’s 3rd Law: for every action, there is an equal and opposite reaction) into the vehicle seat back. All the energy that goes into stretching of webbing and vehicle seat compression has to have a place to go, hence rebound. Rebound with a typical rear-facing carseat usually has 1/3 the energy of the initial crash by the time the carseat impacts the vehicle seat. On a carseat with a load leg, since the downward motion is limited and that energy has been absorbed by the vehicle and the carseat, the rebound will be reduced.

Britax nicely explains rebound in this video (though note that the RF is 5 times safer has been found to be erroneous, but we do know RF to the limits of the carseat is safest).

You can also see rebound on a carseat that doesn’t have rebound control (either with a load leg or with an anti-rebound bar) below. Remember that crash tests look scary, but that as stated above, rebound has typically 1/3 the energy of the initial crash. While there have been injuries to legs on rebound, they have been relatively minor (compared to what can happen forward-facing) and very few. All rear-facing carseats without rebound control will look similar to this one.

On viewing the Clek Liing rear-facing only carseat crash test video below, you can see that the carrier moves slightly on the base, but the base doesn’t move due to installation with rigid LATCH and the load leg. Energy is transferred to the floor and Clek claims crash forces are reduced by more than 40%. Energy is released on rebound but is slight compared to a carseat lacking the load leg feature.


There are carseats, both rear-facing only infant seats and convertible seats, that have anti-rebound bars (ARBs); it’s a more common feature than the load leg. Anti-rebound capability is required in Canada, so Canadian carseats may have it built in to the structure versus having an ARB that must be attached rear-facing.

Alternatives to Using a Load Leg


One alternative to using a load leg on a rear-facing only carseat is installing the carrier without the base Euro-style. This requires that the carrier have a clip or other feature on the back of the seat allowing the shoulder belt to be routed behind the child’s head; not all seats allow this. Having the shoulder belt wrapped around behind the seat supports it and keeps it from rotating down.

Another is installing a convertible using a rear-facing tether Australian-style (Aussie-style). The tether wraps around the back of the carseat and attaches to the vehicle’s tether anchor. Clek has the Q-Tether for its Foonf and Fllo convertibles.

Things to Think about When Using a Load Leg:
  • Load legs must firmly touch the floor, but not lift the base off the vehicle seat or alter the advised recline angle.
  • Check that the load leg is locked into position. Most have a visual cue to help you determine if it’s locked correctly.
  • Some vehicle seats may be too deep for the load leg to unfold naturally over the edge of the cushion. If that’s the case, store the load leg or use a different back seat position.
  • Some center seats have a hump on the floor that makes it incompatible with fully extending the load leg. If that’s the case, store the load leg or use a different back seat position.
  • Check your vehicle owner’s manual if you own a vehicle with in-floor storage areas. Some vehicles explicitly forbid the use of load legs over these storage areas.

For being around a long time, load legs are certainly starting to make a splash in the market here. As with any carseat, a base with a load leg may not work well in your vehicle or with other carseats in your car. Because of their reduction in crash forces, a carseat with a load leg is a feature worth considering if you can find one in your price range with other features you like and that you’ll use correctly each ride.

Carseats with Load Legs

Scroll → to see full table

Model Price Rigid LATCH CarseatBlog Review CarseatBlog Recommended Seat
Clek Liing $459.99 Yes Yes
Cybex Aton 2 $229.95 No Yes
Cybex Aton M $399.95 No
Cybex Cloud Q $399.95 No
Cybex Sirona S $549.99 No
Evenflo LiteMax DLX $224.99 No Yes Yes
Evenflo Gold SecureMax $239.99 No
Graco Premier SnugRide SnugFit 35 XT $349.99 No
Maxi-Cosi Coral XP $399.99 No
Maxi-Cosi Mico XP Max $319.99 No
Nuna PIPA/Stokke PIPA/Bug Turtle $319.95 Yes Yes Yes
Nuna Pipa Lite $349.95 Yes Yes
Nuna Pipa Lite R $349.95 Yes Yes
Nuna Pipa Lite LX $399.95 Yes
Nuna Pipa Lite RX $349.95 Yes
Nuna Pipa RX $309.95 Yes Yes
Peg Perego Primo Viaggio 4-35 Lounge $429.99 No
Peg Perego Primo Viaggio 4-35 Nido $349.99 No Yes
Model Price Rigid LATCH CarseatBlog Review CarseatBlog Recommended Seat


  1. Jessica May 26, 2020
    • Heather May 27, 2020
  2. Jessica January 18, 2020
    • Heather January 19, 2020
  3. Velma September 26, 2019
  4. wagonlover January 17, 2019
    • Heather January 18, 2019
  5. Jenifer January 15, 2019
    • Heather January 17, 2019