Updated Chicco NextFit Zip Convertible Carseat Review
I’ll admit that I was a little worried. The Chicco KeyFit is possibly the most well-loved infant seat of all time and the bar was set pretty high for any convertible carseat that would wear the Chicco name. There was no doubt that the expectations were high and they needed to nail this one or else it was going to go down in the carseat history books as the biggest disappointment since the Nania Airway (long story with unhappy ending). Thankfully, my anxiety was for nothing because the Chicco NextFit convertible exceeds every expectation that I had for ease of use and ease of proper installation. Chicco people, you can pat yourselves on the back for another job well done!
The Chicco NextFit Zip is a Recommended Carseats and an Editor’s Pick.
What makes the Chicco NextFit stand out in a crowded field of high-end convertibles?
One word – SuperCinch. Well, technically that’s two words but Chicco has made it one word and trademarked it so that’s what I’m going with. SuperCinch is a force-multiplying system that makes it possible for anyone, even an elderly grandparent, to get a rock-solid installation in less than 1 minute using LATCH. It’s so easy that even my husband can do it properly! Without me hovering. Or coaching. Or leaving post-it notes in the seat. Seriously, it’s that easy. This seat could not only save lives – it could save marriages! 😉
In addition to the incredibly innovative force-multiplying SuperCinch system, Chicco has really gone out on a limb to design and engineer a seat that is very easy for parents and caregivers to use correctly and equally difficult to misuse if you’re actually making an attempt to “do it right”.
NextFit Specs:
- Rear-Facing: 5-40 lbs
- Forward-Facing: 22-65 lbs; 49″ or less; at least 1 year old. *Chicco and the American Academy of Pediatrics (AAP) recommend all children ride REAR-FACING until they reach the weight/height limits of this seat.
- FAA Approved for use on aircraft
- 8 year lifespan before seat expires
There are 4 trim lines. MSRP for the “base” version, the NextFit Sport, is $249. The NextFit Zip is $299. The NextFit Zip Air is $329. The NextFit Zip Max model is $329. The chart below summarizes the differences.
RF Weight limits | FF Weight limits | Harness pads | Infant insert | ComfortFlex™ harness padding | Zip-off cover | AirMesh™ backrest | Extra legroom | |
---|---|---|---|---|---|---|---|---|
NextFit Sport | 12-40 lbs. | 22-65 lbs. | ✓ | |||||
NextFit Zip | 5-40 lbs. | 22-65 lbs. | ✓ | ✓ | ✓ | ✓ | ||
NextFit Zip Air | 5-40 lbs. | 22-65 lbs. | ✓ | ✓ | ✓ | ✓ | ✓ | |
NextFit Zip Max | 4-50 lbs. | 22-65 lbs. | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ |
NextFit Features:
- SuperCinch LATCH tightening system
- No-rethread harness (9 height positions)
- 2 crotch strap/buckle positions
- 2-position chest clip (only on Zip Max model)
- Energy-absorbing EPS foam lines the sides and the headwings
- Lock-offs for rear-facing and forward-facing installations with seatbelt
- 9 recline positions (any position can be used rear-facing or forward-facing to achieve an appropriate recline angle)
- Dual liquid bubble level indicators (one for RF, one for FF)
- Smooth bottom base with grip material won’t damage vehicle upholstery or slide around on slippery leather seats
NextFit Measurements:
- Lowest harness height setting: 5.5″ with newborn insert; 7.5″ without insert
- Tallest harness height setting: 17.5″
- Crotch strap positions: 3″ with insert; 4″ or 6″ without insert
- Seat pan depth (leg room/thigh support): 14″
- Internal seated height room (highest position): 26″
- Base “footprint”: 17″ front to back; 14.5″ at widest point across
- Weight: 25.2 lbs. (according to my digital bathroom scale)
Installation Comments:
The NextFit passed every challenge as I installed it in a wide variety of vehicles and seating positions both rear-facing and forward-facing using either LATCH or seatbelt. I installed it in bigger vehicles, smaller vehicles, old jalopy vehicles, new luxury vehicles with contoured rear seats and protruding head restraints, crew cab pick-up trucks with funky tether routing and even in the 3rd row center of my 2005 Ford Freestar minivan which is notoriously problematic for most FF carseat installations due to lousy belt geometry. The only installation that gave me any trouble at all was the 3rd row center of my minivan (pic below). The shoulder belt in this seating position originates from the ceiling and the lap portion of the belt is anchored forward of the bight by a good 2″. That combination makes it extremely difficult to install any forward-facing carseat securely. Typically what happens in this seating position is that the carseat appears tight (doesn’t move more than 1″ from side-to-side) but when you test for tightness from front-to-back, the carseat slides forward several inches. I ran into this exact problem when I first tried to install the NF forward-facing with the seatbelt in this seating position. However, I don’t give up that easily. I’ve been installing carseats for over 16 years and I’ve learned a few tricks of the trade along the way. I’m not going to go into too much detail but suffice to say that I went “old school” on the installation (with both knees in the seat and using the reclining seat back trick) and I wound up with a tight install that didn’t move at all side-to-side and moved less than 1″ from front-to-back. Having a lock-off on the NF really helped in that situation. Honestly, that was the only installation in the multiple vehicles that I tested that gave me even the slightest bit of trouble. Rear-facing in that same seating position using seatbelt (pic below) wasn’t a problem. Every other installation was basically a walk in the park.
Installing with LATCH:
Rear-facing: you can install using the lower LATCH anchors until your child reaches 35 lbs. When your child weighs between 35 – 40 lbs., you should install your rear-facing NextFit with seatbelt using the lockoff.
Forward-facing: You can use the LATCH system in your vehicle (lower anchors and tether) to install the NextFit until your child weighs 40 lbs. If your child weighs between 40-65 lbs., install with the seatbelt using the lockoff. Always use the top tether strap if you have a tether anchor for that seating position.
NextFit does NOT allow center LATCH installations with “Non-Standard Spacing” so you can only take advantage of the easy LATCH installations with SuperCinch if you are installing in a dedicated LATCH seating position with standardized spacing (280 mm).
The lower LATCH connectors are the premium push-on connectors made by SafeGuard. The connectors are also “non-handed” which just means that you don’t have to remove the LATCH belt from the beltpath to switch the orientation of the lower anchor connectors. You can simply slide the LATCH belt from the rear-facing beltpath to the foward-facing beltpath and your lower anchor connectors will always be facing the right direction as you attach them to the lower anchor bars in your vehicle. Just to clarify, the lower LATCH connectors have an “up” side and they need to be attached to the lower anchors facing the right direction. It should look like a stapler (with the fat side on top) clamping down on the anchor bar.
Installation using SuperCinch is literally… a cinch! Check out our previous video on installation with SuperCinch:
Tether:
Tethering is required for all forward-facing installations when a tether anchor is available. If the vehicle does not have any top tether anchors or if the NextFit must be installed in a seating position that does not have a designated top tether anchor then it is not considered a misuse to install without tethering. However, Chicco really wants the seat to be tethered (and so do we!) regardless of whether you are installing forward-facing using the lower LATCH anchors or the seat belt. Do NOT use the tether strap when the NextFit is installed rear-facing. In that case, store the tether hook in its storage compartment on the back of the shell.
Installing with Seatbelt:
The openings on the sides of the shell for the beltpath are small but it’s not an issue because you access the beltpath from the access panel in the front of the seat.
I tried numerous rear-facing and forward-facing installations using the seatbelt and ran into very few issues. Use one lockoff when installing with seatbelt. If your seatbelt has a switchable retractor you may opt to switch it into locked mode after you lock the seatbelt inside the lock-off. It’s redundant and unnecessary (and I wouldn’t recommend doing this with a RF install because it could cause the seat to start tilting) but it’s not considered a misuse if you lock the seatbelt by switching it into ALR mode after securing the belt in the lock-off. Again, it’s just redundant and unnecessary because locking the seatbelt using the lock-off provides all the necessary pre-crash positioning.
In general, the NextFit doesn’t take up too much room in the rear-facing position – especially if you don’t need a maximum recline angle for a newborn. Below are pictures (left to right) of RF installations in an Audi Q5, Ford Freestar and Volvo S60 R-Design.
The design of the shell and the headwings seems to work well with a variety of head restraints when the seat is installed forward-facing.
2012 Ram 1500 Crew Cab: The NextFit installed beautifully both RF and FF in the outboard positions of this vehicle. Tethering was a challenge but that was due to the funky tether routing required in this vehicle. I was able to fit the tether and the tether adjuster hardware through the loop of webbing directly behind the seating position and attach the tether hook to the tether anchor behind the center seating position (as required in this vehicle) but getting it back out proved to be a little time-consuming. Definitely not something I would want to have to wrestle with on a frequent basis – but none of that is the carseat’s fault. The NextFit was incompatible with the center seating position in this vehicle because for some odd reason the rear center seat in a Ram 1500 is considerably more shallow than the outboard seats. This caused too much overhang. Chicco is very specific that no more than 3″ of the footprint of the base may hang over the edge of the vehicle seat.
Installation with inflatable seat belts is NOT allowed.
Fit to Child Comments:
With Infant Insert:
The infant insert is recommended (but not required) for babies who weigh between 5-11 lbs. If your baby fits fine without the insert than you can skip it. In general, the smaller the baby – the more likely it is that you’re going to need the infant insert to get a proper fit with the harness straps being positioned at or slightly below the baby’s shoulders. I was pleasantly surprised when I saw that the Nextfit with the infant insert provides a good harness fit on the very tiny preemie doll from Huggable Images that we use to assess whether a seat is really likely to fit a small newborn or a preemie. The minimum weight rating on the NextFit is 5 lbs. but the fact that it does fit the 4 lbs. 17″ preemie doll pretty well means that it should provide a good fit even for smaller-than-average newborns if you decide that you want to skip the infant seat and use a convertible right from the start. If you need to use the NextFit in the lowest harness height setting then you need to fold the back padding panel under to allow the headrest to lock into its lowest position. If you don’t fold it under then the cover will actually get in the way and the headrest won’t lower all the way down.
Preemie Doll – With Infant Inserts
20″ Newborn Doll – Without Infant Insert (fit beautifully)
Rear-facing 3 year old:
The NextFit allows any headrest position to be used when the seat is installed rear-facing as long as the harness straps are positioned at or slightly below the child’s shoulder level. The rear-facing height limits are so generous that children will almost certainly fit height-wise until they reach the max RF weight limit of 40 lbs.
The maximum height limit for the NextFit is 49″ tall or the seat can be outgrown by height once the child’s shoulders are above the harness slots in the highest height setting. Kids with longer-than-average torsos will always outgrow seats more quickly just because of the way they are proportioned.
NextFit “ZIP” Models:
The NextFit Zip model has a cover that zips off and on for easy cleaning. Does it zip off easily? Yes, it’s really a great feature! But it’s important to note that only the main portion of the cover zips off. The cover on the adjustable headrest and a flap of the cover that is attached to it does not zip off (pic below) but it was easy for me to remove and replace that part of the cover too. There is an edge of fabric with one side of the zipper that remains attached to the shell. It’s not likely that you would need to remove that edge piece but it is possible to remove that too, if necessary. Pictured below is the NextFit Zip Air model. We have a separate review of that seat HERE.
FAA-Approval/Lifespan/Inflatable SeatsBelts
- FAA-approved for use on a plane
- 8-year lifespan before expiration
- Installation with inflatable seatbelts (found in some Ford/Lincoln/Mercedes Benz vehicles) is NOT allowed. Use LATCH if possible or move the seat to a different seating position which does not have an inflatable seatbelt.
NextFit Advantages:
- Fits a wide range of children well – including small newborns
- Great seat for extended rear-facing (for kids under 40 lbs.)
- Tall top harness height setting should get a lot of kids to the point where they are big enough and mature enough to transition to a booster (roughly age 5-7)
- Super easy installation with LATCH using SuperCinch technology
- Premium push-on lower LATCH connectors
- Easy to switch the lower LATCH connectors from rear-facing beltpath to forward-facing beltpath and vice versa
- RF & FF lock-offs for seatbelt installations
- 9 position no-rethread harness makes it easy to adjust the harness height when your child has a growth spurt
- 9 recline positions practically guarantee a perfect recline angle in almost any vehicle without needing noodles
- Relatively easy to tighten and loosen harness straps
- Harness straps are thick and not prone to twisting
- Buckle is easy to buckle and unbuckle
- Doesn’t take up a lot of room rear-facing (especially if you don’t need the full recline for a newborn). This makes it a good option for smaller cars and for tall parents who may need to have the front seat all or most of the way back.
- Premium fabrics with extra padding for comfort
- Zip models have cover that is very easy to remove
- Cover and infant insert can be machine washed in cold water (delicate cycle, mild detergent, hang to dry)
- Smooth bottom base won’t damage vehicle upholstery
- Instruction manual is clear and well-written with easy-to-understand diagrams
NextFit Disadvantages:
(In all fairness these aren’t necessarily problems but I list them here to inform potential consumers of specific NextFit issues)
- Heavy & bulky
- Due to LATCH weight limits you must switch to a seatbelt installation once the child weighs more than 35 lbs. rear-facing or more than 40 lbs. forward-facing (not a big deal since you have lock-offs for easy seatbelt install but not quite as easy as using SuperCinch)
- Made in China (to be fair I should point out that so are many other good quality, high-end carseats)
Conclusion:
As you can see the “pros” of the Chicco NextFit far outweigh the few “cons” which is why this seat is on our list of Recommended Carseats as an Editors’ Pick. And while there is no such thing as a perfect carseat, the Chicco NextFit is clearly a well-designed and well-thought-out convertible. Nothing on the NextFit seems cheap or flimsy or lacking in any way. Yes, it’s heavy and bulky but it’s clearly a good quality, high-end carseat. The premium padding is the ultimate icing on the cake, in my opinion. If you want your child to feel like he or she is sitting on a cloud – the NextFit can definitely deliver.
Of course, the best advice for any carseat is to try before you buy, whenever that’s possible. If that just isn’t an option for you then keep in mind that ordering directly from Amazon will usually give you the benefit of free shipping and free returns if it doesn’t work out for some reason.
Thank you to Chicco USA for providing the NextFit sample used in this review. No other compensation was provided and the opinions and comments are entirely those of CarseatBlog.
For more info (and some great instructional videos) see the Chicco webpage for NextFit: http://www.chiccousa.com/nextfit
Updated Jan 2021
CarseatBlog Experts Rating
Editors’ Pick Premium Category: NextFit Zip
Also Recommended: NextFit Sport
Wow! What a comprehensive review. I’ve been stalking several car seat review sites. Hah! Just so lost on where to start looking for a convertible car seat for our 9 m/o who is quickly growing out of her infant carrier. The NextFit looks pretty stylish and easy to use! This is a strong contender for our next car seat!
I love my Chicco keyfit and am so excited to see the convertible! I really like the versatile positions as my kids are picky!
Wonderful blog! Thanks for all the helpful information! This car seat is number 1 on my list but I have to admit it so hard to choose with all the great seats out there.
I’ve heard about this car seat for months and finally had the chance to see it in person at Target. LOVE at first sight!! The only “concern” was that the back of the car seat cover seemed flimsy and flopped around as I moved the headrest up (maybe a bit of velcro or thicker padding???), and the harness seemed hard to loosen at the lowest newborn position. When the headrest was higher, it wasn’t a problem though. But everything else I loved, loved, loved. The recline adjuster is smoother than butter, SO much better than a competing convertible on the shelf nearby. Would LOVE to own a Nextfit!
I remember seeing the Chicco KeyFit at Lifesavers for the first time, oh, SEVERAL years ago now and being so impressed at its ease of use. When choosing a seat for my first baby, I *did* try other infant seats but returned to a long-time favorite, the KeyFit. Baby is arriving sometime in the next week, and his KeyFit has been installed in my car for weeks. 🙂 I’m so glad that Chicco has released the NextFit… we’ll see if that will be his next seat after he outgrows the KeyFit!
I love the superior protection this seat appears to offer and it is very sleek looking 🙂 I wish you could use the seat without the shoulder/chest pads though. Looks like it would be a great seat!
I really appreciate that this seat can be used from little to big. And that SuperCinch is definitely a winning idea.
I really appreciate learning so much about this car seat – I am pregnant with my first so I am doing a ton of car seat research so this blog and reviews such as this are tremendously helpful!
Do you know if this seat will come with accessories such as a travel bag for checking it at the airport, etc? I know Britax and some other brands offer these types of accessories.
I love that this is so versatile for the growing baby/child and will last such a long time!
Thanks for this review. I love that you mentioned its really easy to install. With a baby on the way I’m looking for a new seat that has great reviews and doesn’t break the bank.
Thank you for the review. We are so pleased with our Keyfit 30, but my child is quickly outgrowing it. Can’t wait to get the Nextfit. So glad to hear that the seat is made for ERF.
This review is great! I have been looking for a convertible carseat for a few weeks now. I like that the Nextfit is so easy to install. It will take the guess work out of it. But I LOVE that it has multiple recline positions so I’m sure it will fit in my car!
Thanks for the great review! I am looking for a convertable seat for my 6 month old baby, who will be outgrowing her infant seat very soon. I love that it goes up to 40 pounds rear facing!
We have the Chicco KeyFit and love it! My daughter is just about to outgrow it (because of height) so we are searching for the perfect convertible seat. She is a tall girl so I was happy to read in your review that the NextFit has enough room that she should be able to stay rear facing for a long time. Thank you for the info!
I really like the informative post. And wow, 8 year lifespan, that’s great!
Thanks for the amazing review. The superCinch looks superAmazing. How does that compare to Evenflo,s sureLatch as far of ease of install is concerned?
I love the color Intrigue, I also love that Smooth bottom base with grip material won’t damage vehicle upholstery or slide around on slippery leather seats.
Thanks so much for this very in-depth review.
That’s a pretty incredible car seat! I love the easy installation and 9 recline positions. The most through car seat review I’ve seen! This would be wonderful for our toddler 🙂
I love how easy it is to install.
Thanks for the great review. I have been saying that chicco should make a convertable for years. I am SO glad they finally did.
I love the thorough review! I’ve been looking around for a easy to install, comfortable seat that can rear face to 40lbs+. I’d like my “little” guy to RF for a long time, and he is already 25lbs at 7 months. Thank you for doing reviews like this on so many different models, it makes my job (deciding what to get) just a little bit easier.
I love the inch or less from the top shell rule for rear facing! I’m a nanny and have no idea how tall “my” kids are. I just know how they fit in the seats.
I’m really impressed with this seat from Chicco. I have been dying for them to come out with a convertible since their infant seat was such a hit with this. I think my favorite thing about this seat is the recline positions. Our Radian can be so frustrating to install because it only has one recline position RF, and it’s very tricky to install it at a different angle. This seat looks so easy. I *wish* it went up to 45 lbs RF, but hey, I won’t be picky 😉 It has really high top harness slots, so it’s going to last kids a LONG time. It looks very comfy to, which is always important! These headwings also look much more user friendly than our current XTSL headwings
Wow, looks like a great car seat. We have two Chicco KeyFit30′s and we’re about ready to graduate our twin boys to the next size car seat. This will be a great contender.
I really love the 9 recline positions! My car seats are somewhat bucket and somewhat bench. Anything that alleviates a noodle/rolled up towel is pretty freaking awesome! 🙂
I have two favorite features of this seat – 1. I LOVE how easy it is to install. It takes all of the guesswork out of installation for those who don’t do it often (eg grandparents)which in turn helps me feel at ease about someone installing a seat without me being present. And 2. I truly appreciate the chest clip that can be narrow or wider. I hate car seats with HUGE chest clips and love the idea that they have made a 2 in 1 chest clip of sorts to fit small and large babies/children!
Great seat Chicco!